FLUID CELL FORMING PRESSES

VERSON WHEELON, MODEL 29000R-50-116, FLEX-DIE RUBBER PAD, S/N 27296, FLUID FORMING CAPACITY TONNAGE 29,000 FORMING PRESSURE: THRU 10,000 P.S.I., TRAYS: TWO TRAY SIZE AT TOP 50″ X 116″ (1,270MM X 2,946.4 MM) RIGHT TRAY AREA AT A 6 INCH (152.4MM) DEPTH 42″ X 109″ (1,079.5MM X 2,768.6MM), LEFT TRAY AREA AT A 10 INCH (254MM) DEPTH 37″ X 104″, MOTOR DRIVES: ALL MOTORS WIRED 440 VOLTS, 3 PHASE, (2) EVACUATE HIGH PRESSURE PUMPS 75 HP & 150 HP, (1) ACC PUMP 30 HP (1) PILOT PUMP 20 HP, (1) VACUUM PUMP 15 HP, (1) FILTER PUMP 1/4 HP, CONTROLS: WIRED 115 VOLTS, OPERATOR CONTROL STATION LOCATED CENTER OF BARREL, (2) SIDE CONTROLS STATIONS LOCATED AT END OF EACH BARREL WITHEMERGENCY STOP BUTTONS, EQUIPPED WITH: (1) POWER UNIT AND OIL RESERVOIR, (1) NITROGEN INTENSIFIER PUMP. (2) THROW PAD ROLL-UP DEVICE FOR EACH TABLE, (1) ACCUMULATOR HYDRAULIC OIL STORAGE TANK, (1) FLUID CELL, (1) RUBBER PAD ELECTRICAL STARTER PANELS, COMPLETE FACTORY SAFETY GUARDS,  DIMENSIONS 342.16″ L-R X 120″, F-B X 1873/8″HEIGHT WITH FILL LINES,  MAIN CHAMBER WITH FILL LINES, HEIGHT ABOVE GROUND 161 7/8″ (428.63MM), POWER UNIT AND OIL RESERVOIR F-B 96″ X 178″ (2,438.4MM X4,521.2MM, INTENSIFIER 33″ X 33″ X 132″ HT. (38.2MM X 838.2MM X 3,352.8MM), ACCUMULATOR 80″ DIAMETER X 186″ HT. CONTROL PANEL 144″ LR X 18″ FB X 91″ HT., APPROX. WT. 363,700 LBS, (2,032MM DIAMETER X 4,724.4MM HT.) (3,657.6MM FB X 457.2 FB X 2,311.4MM HT

VERSON WHEELON DIRECT ACTING HYDRAULIC FORMING PRESS, MODEL 21000R-50-168, FLEX-DIE RUBBER PAD, S/N 13249, SPECIFICATIONS: FLUID FORMING CAPACITY TONNAGE: 21,000, FORMING PRESSURE: 5,000 P.S.I. MAX., TRAY: (2), TRAY SIZE AT TOP 50″ X 164″ (1,270MM X 4,165.6MM), TRAY AREA AT 5″ DEPTH 44″ X 158″ (1,117.6MM X 4,019.55MM), TRAY AREA AT 7″ DEPTH 38″ X 152″ (965.2MM X 3,860.8MM), MOTOR DRIVES: WIRED 440 VOLTS, 3 PHASE, HIGH PRESSURE PUMPS75 HP (55.2KW), VOLUME PUMP EVACUATING 30 HP (22.07KW), FILTER PUMP 1/3 HP (24.55KW), CONTROLS: WIRED 115 VOLTS, (1) OPERATOR CONTROL STATION, (2) SIDE CONTROLS STATIONS AT END OF BARREL W/EMERGENCY STOP, EQUIPPED WITH: (2) THROW PAD ROLL-UP DEVICE, FLUID CELL, (1) RUBBER PAD, ELECTRICAL STARTER PANELS, COMPLETE FACTORY SAFETY GUARDS, DIMENSIONS POWER UNIT AND RIGHT TRAY 130″F-B X 389″L-R X 144″ ABOVE FLOOR, 18″ BELOW FLOOR OVER-ALL HEIGHT 162″, DIMENSIONS POWER UNIT & RIGHT TRAY (3,302MM) F-B X (9,880.6MM) L-R, (3,657.6MM) ABOVE FLOOR + (457.2MM) BELOW FLOOR OVER-ALL HEIGHT (4,1148MM)

STRETCH WRAP FORMING MACHINE

HUFFORD MODEL A-10 STRETCH WRAP FORMING MACHINE, CAPACITY 17.5 TONS TABLE DIMENSIONS 30” X 65” TABLE HEIGHT 35.5” MAXIMUM PART LENGTH FORMED 219” STANDARD ARM MINIMUM PART LENGTH FORMED 10” MAXIMUM DIE HEIGHT 20” MAXIMUM DIE LENGTH @ 180 DEG. 68” MINIMUM DIE LENGTH @ 180 DEGREE, S/N 24

AUTOMATED ANODIZING/CHEM FILM SYSTEM

2017 BAKER, SYSTEM TYPE: BTA MODEL SL-350, LINE NUMBER A3047, ORDER NUMBER 172675, TOP RAIL SUPPORTED TRANSPORTER, 330 LB MAXIMUM GROSS WEIGHT, (9) 304 STAINLESS STEEL & COOPER FLIGHT BARS, SYSTEM LAYOUT: 14 2” (INCLUDING CATWALK, 52’ 10” OVERALL LENGTH, 14’ OVERALL HEIGHT

5 AXIS VERTICAL MACHINING CENTERS

(2) 2006 HAAS VR-11B, 5-AXIS ARTICULATING HEAD, 120” X, 40” Y, 30” Z, 84” X 36” TABLE, 10000 RPM SPINDLE, THROUGH SPINDLE COOLANT, 20 HP SPINDLE, 40 TAPER, 32 ATC, REMOTE JOG HANDLE, S/N’S 49667, 49668

2006 HAAS VR-9, 5-AXIS ARTICULATING HEAD, XYZ TRAVELS: 84” X, 40” Y, 30” Z, 84” X 36” TABLE, 15000 RPM SPINDLE, 20 HP SPINDLE, 40 TAPER, 24 ATC, SIDE MOUNT TOOL CHANGER, REMOTE JOG HANDLE, S/N 1052742

VERTICAL MACHINING CENTERS

2007 HAAS VF-9/40, XYZ TRAVELS: 84”X 40”X 30”, 84” X 36” TABLE, 10000 RPM SPINDLE, 30 HP, 40 TAPER, 24 ATC, SIDE MOUNT TOOL CHANGER, 2 SPEED GEAR DRIVE, CHIP BLASTER, 4TH AXIS READY, MIDACO SERIES 80SD AUTOMATIC ALUMINUM AUTO DOOR PALLET CHANGER, S/N 1060941

2006 HAAS VF-7B/40, XYZ TRAVELS: 84”X 32”X 30”, 36” X 14” TABLE, 10000 RPM, THROUGH SPINDLE COOOLANT, 30 HP SPINDLE, 40 TAPER,
24 ATC, SIDE MOUNT TOOL CHANGER, 2 SPEED GEAR DRIVE, CHIP BLASTER, AUTOMATIC CHIP AUGER, 4TH AXIS READY, MIDACO SERIES 80SD AUTOMATIC ALUMINUM AUTO DOOR PALLET CHANGER, S/N 1052111

2009 HAAS VF-5D/40, XYZ TRAVELS: 50” X 26” X 25”, 52” X 23” TABLE, 24 ATC, VECTOR DUAL DRIVE, THROUGH COOLANT SPINDLE,
20 HP, 7500 RPM, 40 TAPER, AUTOMATIC CHIP AUGER, HIGH INTENSITY LIGHTING, S/N 1073797

2007 HAAS VF-5SS, XYZ TRAVELS: 50”X  26” X  25”, 52” X 23” TABLE, 24 ATC, HIGH SPEED SIDE MOUNT TOOL CHANGER, INLINE DIRECT DRIVE SPINDLE, 30 HP, 12000 RPM, 40 TAPER, AUTOMATIC CHIP AUGER, HIGH INTENSITY LIGHTING, JOG HANDLE, RENISHAW PROBING SYSTEM, JOG HANDLE, RENISHAW PROBING SYSTEM, S/N 1056788

2007 HAAS VF-4SS APCQ MINI FMS, XYZ TRAVELS: 50” X 20” X 25”, 52” X 18” TABLE, 40 ATC, SIDE MOUNT TOOL CHANGER, THROUGH COOLANT SPINDLE, INLINE DIRECT DRIVE, 12000 RPM, 30 HP, 12000 RPM, 40 TAPER, AUTOMATIC CHIP AUGER, CHIP BLASTER, AUTOMATIC PALLET CHANGER, CHIP BLASTER, S/N 1056650

2005 HAAS VF-4SSAPC, XYZ TRAVELS: 50” X 20” X 25”, 52” X 18” TABLE, 24 ATC, HIGH SPEED SIDE MOUNT TOOL CHANGER, 30 HP, 12000 RPM, 40 TAPER, AUTOMATIC CHIP AUGER, HIGH INTENSITY LIGHTING, AUTOMATIC PALLET CHANGER, S/N 43310

2002 HAAS VF-4 BAPC, VOP-D, XYZ TRAVELS: 50” X 20” X 25” Z, 52” X 18” TABLE, 24 ATC, SIDE MOUNT TOOL CHANGER, THROUGH COOLANT SYSTEM, 30 HP, 10000 RPM, 1200 IPM, 40 TAPER, AUTOMATIC CHIP AUGER, AUTOMATIC PALLET CHANGER, S/N 28304

2004 HAAS VF-4D, VOP-A, XYZ TRAVELS: 50” X 20” X 25”, 52” X 18” TABLE, 24 ATC, SIDE MOUNT TOOL CHANGER, 20 HP, 10000 RPM, 40 TAPER, AUTOMATIC CHIP AUGER, RENISHAW PROBING SYSTEM, 4TH AXIS READY, S/N 38605

2007 HAAS VF-3SS, XYZ TRAVELS: 40” X  20” X 25”, 48” X 18” TABLE, 24 ATC, SIDE MOUNT TOOL CHANGER, 30 HP, 12000 RPM, 40 TAPER, HIGH SPEED AUTOMATIC CHIP AUGER, HIGH INTENSITY LIGHTING, JOG HANDLE, RENISHAW PROBING SYSTEM, S/N 1062023

(4) 2008 HAAS VF-2SS, XYZ TRAVELS: 30” X 16” X 20” Z, 36” X 14” TABLE, 24 ATC, HIGH SPEED SIDE MOUNT TOOL CHANGER, INLINE DIRECT SPIDLE, 30 HP, 12000 RPM, 40 TAPER,  4TH AXIS READY, HIGH INTENSITY LIGHTING, RENISHAW PROBING SYSTEM, S/N’S 1065968, 1065971, 1065953, 1065972

(2) 2007 HAAS VF-2SS, XYZ TRAVELS: 30” X 16” X 20”, 36” X 14” TABLE, 24 ATC, HIGH SPEED SIDE MOUNT TOOL CHANGER, 30 HP, 12000 RPM, 40 TAPER, JIG HANDLE, AUTOMATIC CHIP AUGER, S/N’S 1059023, 1056986

2006 HAAS VF-2D, VOP-B, XYZ TRAVELS: 30” X 16” X 20” Z, 36” X 14” TABLE, 24 ATC, 20 HP, 10000 RPM, 40 TAPER, VICTOR DUAL DRIVE, AUTOMATIC CHIP AUGER, 4TH AXIS READY, S/N 1051900

(2) 2005 HAAS VF-2D, XYZ TRAVELS: 30” X 16” X 20”, 36” X 14” TABLE, 20 HP, 10000 RPM, 40 TAPER, RENISHAW PROBING SYSTEM, AUTOMATIC CHIP AUGER, S/N 46291, 46292

5 & 4 AXIS TRUNNION & ROTARY TABLES

(5) HAAS TR210 & HRT160 ROTARY TABLES

GANTRY ROUTERS

2009 HAAS GR512, 5′ X 12′ TABLE; TRAVELING GANTRY STYLE, 20.5″ UNDER THE BRIDGE, 11″ Z – AXIS STROKE, (10) ATC, TABLE HOLD DOWN SCREW FIXTURES, S/N 1071513

2006 HAAS GR512, 5′ X 12′ TABLE; TRAVELING GANTRY STYLE, 20.5″ UNDER THE BRIDGE, 11″ Z – AXIS STROKE, (10) ATC, TABLE HOLD DOWN SCREW FIXTURES, S/N 1052759

2008 KOMO VR512 MACH XTRM, 5′ X 12′ TABLE, TOOL CHANGER, DYNICS CONTROL, S/N 68621-08

2006 KOMO VR512 MACHINE SHO, 5′ X 12′ TABLE, 10-HEAD QUICK CHANGER, S/N 57952-06

6 PALLET HORIZONTAL MACHINING CENTER

2008 HAAS EC-400PP, XYZ TRAVELS: 22” X 25” X 22”, 6 STATION PALLET POOL, 15.75” X 15.75” PALLETS, AUTOMATIC PALLET CHANGER, 12000 RPM, 40 TAPER SPINDLE, 30 HP, INLINE DIRECT DRIVE SPINDLE, 70 POCKET SMTC, THROUGH COOLANT SPINDLE, CHIP CONVEYOR, LOAD & UNLOAD STATION, RENISHAW PROBING SYSTEM, S/N 2052621

TURNING CENTER

2006 HAAS SL-10T, MAXIMUM TURNING DIAMETER 11″, MAXIMUM TURNING LENGTH 14″, SWING OVER CROSS SLIDE 8″, X AXIS TRAVEL 6.25″, Z AXIS TRAVEL 14.00″, 12 STATION TURRET, 6000 RPM,  1.75” BAR CAPACITY, TOOL PRE-SETTER, HYDRAULIC TAIL STOCK, 12 ATC, 15 HP, AUTOMATIC CHIP AUGER, HAAS SERVO BAR 300 LOADER, S/N 73255

TOOLROOM EQUIPMENT

AMERICAN TURNMASTER AT-1340G LATHE, 6” CHUCK, TAILSTOCK, S/N 13406111720

BRIDGEPORT VERTICAL MILL, SERIES 1, 2 HP, POWER FEED, SONY DRO, S/N BR274747

1999 WEGOMA SD 175 MITERING COLD SAW, 17” BLADE, INFEED/OUT FEED ROLLER CONVEYOR, , S/N 001-0007

DOALL 3613-1 VERTICAL BANDSAW, DUAL TABLE, S/N 440-89349

KALAMAZOO FA-350 AUTOMATIC COLD SAW, 36” THROAT, 14” BLADE, S/N 110

DELTA 12”-14” TILTING ARBOR SAW

SUNNEN MBB-1800 HONE, S/N 73587

BURRKING 760 BELT SANDERS, (6) DAKE ARBOR PRESSES, CLAUSING DRILL PRESSES, VERTICAL PANEL SAW, (60) KURT 8” & 6” MACHINE VISES, HOUTE TOOL HOLDER CARTS, STEEL TABLES AND REALTED ITEMS

100’S OF 50 & 40 TAPER TOOL HOLDERS

WATERJET CUTTING MACHINES

2003 FLOW, 6’ X 12’ TABLE, 60,000 PSI, FLOWMASTER VERSION 6 SOFTWARE, S/N NA

2012 FLOW M2-313B, TABLE SIZE 13X 13M, FLOWMASTER VERSION 6 SOFTWARE, S/N 120465

SHEET METAL FABRICATION EQUIPMENT

2000 NISSHINBO HIQ-1250/50 TURRET PUNCH PRESS, 30 TON, 98” X 49” SHEET SIZE, THICK TURRET, 52 STATION, NISSHINBO PAL-510T CONTROL, S/N 12020

PACIFIC J-SERIES PRESS BRAKE, MODEL J110-12, 10’ X 110 TON CAPACITY, AUTOGAUGE CNC 100 CONTROL, TRAID EAGLE EYE PROTECTION, S/N A516

1996 GREENERD HCA-50-30R8 C-FRAME PRESS, 50 TON, OPEN GAP, S/N 9675110

1995 GREENERD HCA-50-60RS C-FRAME PRESS, 50 TON, OPEN GAP, S/N 9575032

TIMESAVER 37” BELT SANDER

FLADDER-AUT 36” BRUSH DEBURRING MACHINE

L & J OBI PUNCH PRESS, 70 TON

MACHINE TECHNOLOGIES HOT FORMING PRESS, 24” X 24” PLATEN, S/N 87-61701-1

PEXTO 16-18 ROLL, 418E, 4’ X 18 GAUGE, S/N 5/71

SHRINKING & STRETCHING MACHINES

(8) MARCHANT, MODELS 12A, 6FG, 6A, 4A-M

PRESS TYPE SPOT WELDERS

JANDA PVFD3-170-24RTDF, 170 KVA, 36” THROAT, S/N P-3604

SCIAKY SPT 2-30-75-36, 100 KVA, 36” THROAT, S/N 8887

RUBBER BOX PRESS

4 POST, 36” X  60” BED

FILTER PRESS

2017 PAC PRESS, MODEL P4E135-2, 2 CU. FT. CAPACITY, MAX PRESSURE 100/7300, S/N 1559

AIR COMPRESSOR & REFRIGERATED AIR DRYER

INGERSOLL RAND SSR-EP100, 100 HP, S/N F9149U94007

2015 QIUNCY QPNC0600 (A14) UL, S/N CA1847872

STAKE BED TRUCK

2012 HINO MODEL 268 STAKE BED TRUCK, 7.6 L L6 DIESEL ENGINE, LIC# 40915H1, VIN# 5PVNE8JT2C4S54577